Search Results

This paper describes a newly developed HC-adsorption three-way catalyst and adsorption system that reduce cold-start HC emissions with high efficiency. This system is the first of its kind anywhere in the world to be implemented on production vehicles. An overview is given of the various improvements made to achieve higher cold-start HC conversion efficiency. Improvement of conversion performance was accomplished by (1) increasing the thermal stability of the HC adsorbent, (2) improving desorbed HC conversion efficiency and durability and (3) optimizing the geometric surface area (GSA) of the substrate. Concretely, the thermal stability of the adsorbent was improved by enhancing the high-temperature durability of zeolite. Improvement of desorbed HC conversion efficiency was accomplished by improving the OSC material so as to match the temperature rise characteristic and usage temperature of the catalyst.

High strength transmission gears have been developed for use in the final gear set of front-wheel-drive vehicles. The steel used as the gear material has a higher molybdenum content, allowing more austenite to be retained following carburizing than is possible with chromium steel. As a result, the steel can be subjected to higher intensity shot peening by using harder peening particles which are projected by an air-nozzle peening system. With this procedure, the fatigue strength of the gears can be increased 1.6 times over that of conventional gears.

Flow velocity distributions in the passenger compartment were measured from visualized images of particle flow paths obtained with a full-scale model. The flow paths were visualized using an approach that combined a particle tracing method with a pulse-laser light technique. Air was used as the fluid medium with the full-scale passenger compartment model and water was used as the fluid medium with a one-fourth scale model. A comparison of the results obtained with the two models confirmed that there was good agreement between the flow velocity distributions. Using the full-scale model, measurements were also made of the flow velocity distributions when two dummies were placed in the front-seats.

Regulations on the use of chlorofluorocarbons (CFCs) are being adopted around the world to protect the ozone layer from these chemicals. It is Nissan's position that environmental protection is one of the most important issues facing automotive engineers today. Accordingly, with the aim of ensuring a healthier environment, we have been working for approximately three years on the development of an automotive air conditioning system using the HFC-134a refrigerant in place of CFC-12. Starting with the introduction of this air conditioning system in a new production model scheduled for release in March 1992, the system is expected to be used in all new models for North America by the end of 1993. This paper describes the HFC-134a automotive air conditioning system from the standpoint of the design changes required in comparison with a conventional CFC-12 system and technical measures needed for vehicle application.

The FFVs under study operates on either M85 or M0 or any mixture of the two. Nissan has been actively conducting reseach and development on flexible fuel vehicles (FFVs) to explore the possibilities for long-range energy conservation and air quality improvement. The engine converted for use in these FFVs is a 1.6 liter, four-cylinder in-line powerplant, with dual overhead camshafts and four valves per cylinder. It employs the Nissan Variable valve timing Control System (NVCS). The fuel sensor for measuring the methanol concentration in the fuel has been improved both in terms of accuracy and durability. This paper describes the engine performance and exhaust emission levels (formaldehydes unburned methanol and HC emissions) obtained with both M85 and M0.

This paper describes a study of drag reduction devices for production pick-up trucks with a body-on-frame structure using full-scale wind tunnel testing and Computational Fluid Dynamics (CFD) simulations. First, the flow structure around a pick-up truck was investigated and studied, focusing in particular on the flow structure between the cabin and tailgate. It was found that the flow structure around the tailgate was closely related to aerodynamic drag. A low drag flow structure was found by flow analysis, and the separation angle at the roof end was identified as being important to achieve the flow structure. While proceeding with the development of a new production model, a technical issue of the flow structure involving sensitivity to the vehicle velocity was identified in connection with optimization of the roof end shape. (1)A tailgate spoiler was examined for solving this issue.

The purpose of this work was to gain a fundamental understanding of which fuel property parameters are responsible for particulate emission characteristics, associated with key intermediate behavior in the engine cylinder such as the fuel film and insufficient mixing. Accordingly, engine tests were carried out using various fuels having different volatility and chemical compositions under different coolant temperature conditions. In addition, a fundamental spray and film visualization analysis was also conducted using a constant volume vessel, assuming the engine test conditions. As for the physical effects, the test results showed that a low volatility fuel displayed high particulate number (PN) emissions when the injection timing was advanced. The fundamental test clearly showed that the amount of fuel film on the impingement plate increased under such operating conditions with a low volatility fuel.

This paper describes a new 1.6-liter four-cylinder gasoline turbocharged engine with a direct injection gasoline (DIG) system and a twin continuously variable valve timing control (CVTC) system. Demands for higher environmental performance make it necessary to improve engine efficiency further. At the same time, improvement of power performance is important to enhance the appeal of vehicles and make them attractive to consumers. In order to meet these requirements, a 1.6-liter direct injection gasoline turbocharged engine has been developed. By using many friction reduction technologys, this engine achieves the high power performance of a 2.5-liter NA(Naturally Aspirated) gasoline engine and low fuel consumption comparable to that of a smaller displacement engine. In addition, this engine achieves low exhaust emission performance to comply with the US LEV2-ULEV and EU Euro5 emission requirements.

Reducing vehicle fuel consumption has become one of the most important issues in recent years in connection with environmental concerns such as global warming. Therefore, in the vehicle development process, attention has been focused on reducing aerodynamic drag as a way of improving fuel economy. When considering environmental issues, the development of vehicle aerodynamics must take into account real-world driving conditions. A crosswind is one of the representative conditions. It is well known that drag changes in a crosswind compared with a condition without a crosswind, and that the change depends on the vehicle shape. It is generally considered that the influence of a crosswind is relatively small since drag accounts for a small proportion of the total running resistance. However, for electric vehicles, the energy loss of the drive train is smaller than that of an internal combustion engine (ICE) vehicle.

A continuously variable valve event and lift (VEL) system, actuated by oscillating cams, can provide optimum lift and event angles matching the engine operating conditions, thereby improving fuel economy, exhaust emission performance and power output. The VEL system allows small lift and event angles even in the engine operating region where the required intake air volume is small and the influence of valvetrain friction is substantial, such as during idling. Therefore, the system can reduce friction to lower levels than conventional valvetrains, which works to improve fuel economy. On the other hand, a distinct feature of oscillating cams is that their sliding velocity is zero at the time of peak lift, which differs from the behavior of conventional rotating cams. For that reason, it is assumed that the friction and lubrication characteristics of oscillating cams may differ from those of conventional cams.

HC emission standards will be tightened during the 1990's in the US. A key issue in reducing HC emission is improving the warm-up characteristics of catalysts during the cold start of engines. For this purpose, studies are under way on reduction of heat mass of ceramic substrates. Reduction of cell walls in substrates to thickness smaller than the current thickness of 12mil or 6mil has resulted in reduced heat mass, and also reduced flow restriction of substrates. The warm-up characteristics of low bulk density catalysts are better than those of high bulk density, i.e., the warm-up characteristics of thinner wall or lower cell density catalysts are better than those of thicker wall or higher cell density catalysts. A relationship between geometric surface area and warm-up characteristics is observed.

In the Japan Clean Air Program II (JCAP II) Diesel WG, effects of fuel properties on the performance of two types of diesel NOx emission aftertreatment devices, a Urea-SCR system and a NOx storage reduction (NSR) catalyst system, were examined. For a Urea-SCR system, the NOx emission reduction performance with and without an oxidation catalyst installed in front of the SCR catalyst at low exhaust gas temperature operation was compared. For an NSR catalyst system, the effect of fuel sulfur on both emissions and fuel economy during 50,000 km driving was examined. Furthermore, effects of other fuel properties such as distillation on exhaust emissions were investigated. The results show that sulfur is the influential factor for both devices. Namely, high NOx emission reduction performance of the Urea-SCR system with the oxidation catalyst at low exhaust gas temperature operation is influenced by sulfur.

Clarifying the impact of ETBE 8% blended fuel on current Japanese gasoline vehicles, under the Japan Clean Air Program II (JCAPII) we conducted exhaust emission tests, evaporative emission tests, durability tests on the exhaust after-treatment system, cold starting tests, and material immersion tests. ETBE 17% blended fuel was also investigated as a reference. The regulated exhaust emissions (CO, HC, and NOx) didn't increase with any increase of ETBE content in the fuel. In durability tests, no noticeable increase of exhaust emission after 40,000km was observed. In evaporative emissions tests, HSL (Hot Soak Loss) and DBL (Diurnal Breathing Loss) didn't increase. In cold starting tests, duration of cranking using ETBE 8% fuel was similar to that of ETBE 0%. In the material immersion tests, no influence of ETBE on these material properties was observed.

Emission regulations for diesel-powered vehicles have been gradually tightening. Installation of after-treatment devices such as diesel particulate filters (DPF), NOx storage reduction (NSR) catalysts, and so on is indispensable to satisfy rigorous limits of particulate matter (PM) and nitrogen oxides (NOx). Japan Clean Air Program II Oil Working Group (JCAPII Oil WG) has been investigating the effect of engine oil on advanced diesel after-treatment devices. First of all, we researched the impact of oil-derived ash on continuous regeneration-type diesel particulate filter (CR-DPF), and already reported that the less sulfated ash in oil gave rise to lower pressure drop across CR-DPF [1]. In this paper, impact of oil-derived sulfur and phosphorus on NSR catalyst was investigated using a 4L direct injection common-rail diesel engine with turbo-intercooler. This engine equipped with NSR catalyst meets the Japanese new short-term emission regulations.

Technologies for reducing fuel consumption have attracted strong interest in recent years amid the heightened concern about global environmental protection. At Nissan, we have been focusing on the development of electronically controlled continuously variable transmissions (CVTs) since the early 1980s as a promising technology for reducing fuel consumption. That work has led to the commercialization of the world's first belt-drive CVT that is suitable for application up to 2.0-liter class passenger cars. The practical use of CVTs has so far been limited to cars mounted with small displacement engines of the 1.6-liter class. The belt-drive CVT described here incorporates new technology for transmitting greater torque and also has product attributes suitable for use on upscale passenger cars, making it applicable to 2.0-liter class models.

One advantage of a direct-injection S.I. engine is lower fuel consumption due to the use of lean stratified charge combustion. Another advantage is greater power output resulting from evaporation of the fuel in the cylinder. A critical factor in making the most of these advantages is to achieve optimum mixture formation for both stratified and homogeneous charge combustion. To achieve the optimum mixture, the new direct-injection S.I. V-6 engine adopts a piston with a shallow bowl, a valve that changes in-cylinder air motion between swirl and tumble by opening and closing one side of separated air intake port, an air intake port that has optimized inward and port angle to induces swirl in the piston bowl, and a CASTING NET injector that injects the hollow cone spray in a deflected pattern toward the spark plug.

Valve deposits in gasoline engines increase with time, absorbing fuel during acceleration and releasing fuel during deceleration. Valve deposits insulate the heat release from the cylinder and this phenomenon is the cause of bad fuel vaporization. In this way, the deposits greatly affect the driveability and exhaust emissions. Using a 3.OL MPI(Multipoint Injection) engine, we measured the quantity of fuel that deposits at the intake port, and the throttle response (using a wall-flow meter made by Nissan Motor Co.1), 2) to study the deposits effect on driveability and exhaust emissions at a low temperature. The deposits were formed on the intake valve surface (about 8.0 on the CRC deposit rating scale) through 200 hours of laboratory engine stand operation. At low temperature, C9 and C10 hydrocarbons tend to stick to the intake port surface and intake valve as “wall-flow”; this is one cause of bad driveability.

With the aim of improving the air quality in large cities, the California Air Resources Board (CARB) has stipulated that non-methane organic gas (NMOG) composed of carbon numbers from C1 to C12 must be reduced for vehicle categories designated as Transitional Low Emission Vehicles (TLEVs), Low Emission Vehicles (LEVs), Ultra low Emission Vehicles (ULEVs), and Zero Emission Vehicles (ZEVs). Although considerable research work has been done on this issue to date, the entire picture is still not clear. Studies done by the authors have been aimed at providing a better understanding of the potential for reducing automotive tailpipe emissions by using several clean fuel candidates. The major questions of concern are the extent to which emissions of certain species can actually be reduced and what fuel can provide the best performance under a reduced NMOG condition.

Nissan has developed a non-methane organic gas (NMOG) emission measuring method based on California Air Resources Board (CARB) procedures.1) In addition, a system to analyze the chemical species present in the exhaust gases at Low Emission Vehicles (LEV) and Ultra Low Emission Vehicles (ULEV) levels has been created. It was found that when using an electrically heated catalyst (EHC) to achieve the low emissions for LEV and ULEV levels, the interference between exhaust HC species and the contamination of the analyzing system are a serious problem for the measurement of speciated emissions. The methyl tertiary butyl ether (MTBE) contained in reformulated gasoline can interfere with HC speciation in the Chromatogram, requiring that the automatically speciated results be checked by a trained operator. The low exhaust HC emissions of bags 2 and 3 in the Federal Test Procedure (FTP) are nearly equal to that of the background air utilized in the constant volume sampler (CVS) dilution.

The California Low-Emission Vehicle (LEV) standards mandate a reduction in non-methane organic gases (NMOG). With the aim of analyzing NMOG emissions, a comparison was made of the hydrocarbon species found in the exhaust gas when different types of catalyst systems and fuel specifications were used. NMOG emissions are usually measured by removing methane from the total hydrocarbon (THC) emissions and adding aldehyde and ketone emissions. The NMOG level found in this way is thus influenced by the rate of methane in THC emissions. Another important factor in the LEV standards is specific reactivity (SR), indicating the formation potential of ozone, which is one cause of photochemical smog. Specific reactivity is expressed by the amount of ozone generated per unit weight of NMOG emissions, and is affected by the respective proportion of hydrocarbon species in the total NMOG emissions.